Menu

wfadmin

About wfadmin

Posts by :

Replacing the Thermal Fuse in Your ghd Hair Straightener​

0

Replacing the Thermal Fuse in Your ghd Hair Straightener

Introduction:

The ghd hair straightener is a popular styling tool, but like any electronic device, it can experience technical issues. One common problem is the failure of the thermal fuse. Replacing the thermal fuse is a delicate process, but it can be done at home with the right tools and a bit of patience. This guide will walk you through the steps.

Safety First:
Before you begin, ensure your safety. Unplug the straightener and allow it to cool down completely. Work in a well-lit, uncluttered area. Remember, dealing with electronic devices involves risks, so if you’re not confident in your ability to perform these repairs, consider seeking professional help.

Tools You’ll Need:

  • A new thermal fuse compatible with your ghd model.
  • A set of small screwdrivers.
  • A pair of tweezers or needle-nose pliers.
  • Heatproof tape.

Step-by-Step Guide:

  1. Open the Straightener: Start by removing the screws that hold the straightener together. This will vary depending on your ghd model, so refer to the user manual or online guides for specific instructions.

  2. Locate the Thermal Fuse: Once open, locate the thermal fuse. It’s typically a square ceramic component connected to the switch side heater plate.

  3. Remove the Old Fuse: Carefully remove the old fuse. Be gentle to avoid damaging the wiring or other components.

  4. Install the New Fuse: Take your new thermal fuse and insert the wires from the screws you removed the old one. Ensure the connections are secure and there are no loose wires.

  5.  

  6. Reassemble the Straightener: Carefully put the straightener back together, ensuring that no wires are pinched or components misaligned. Screw everything back into place.

  7. Test Your Straightener: After reassembly, plug in the straightener and test it to make sure it heats up properly. If it doesn’t work, or if you notice any unusual behavior, unplug it immediately and consult a professional. like ourselves

Conclusion:
Replacing the thermal fuse in your ghd hair straightener can restore its functionality, saving you the cost of buying a new one. However, remember that working with electrical components can be risky. If you’re not confident in your ability to safely carry out these steps, or if the problem persists, it’s best to seek professional assistance.

Please note, this article is intended for informational purposes and does not substitute for professional advice. Handling electronic devices can be hazardous, and improper handling can lead to damage or injury.

Troubleshooting Common Issues of ghd Hair Straighteners

0

Troubleshooting Common Issues ofghd Hair Straighteners

Introduction

ghd hair straighteners are renowned for their quality and durability. However, like all electronic devices, they can occasionally encounter problems. Understanding how to diagnose common faults can help you determine whether a professional repair or replacement is needed. Here’s a guide to troubleshooting some common issues.

GHD straighteners do not heat up

  • Check the Power Source: Ensure that the straighteners are plugged in properly and that the electrical outlet is working.
  • Inspect the Cord: Look for any signs of damage to the cord, such as fraying or kinks, which could indicate a wiring issue.
  • Internal Faults: If there are no visible issues and the device still doesn’t heat up, it could be an internal fault like a broken heating element.

GHD straighteners overheat

  • Faulty Thermostat: This could indicate a problem with the thermostat, which regulates the temperature. Generally this would cause the internal thermal fuse to blow, but in some cases, ghds can overheat and operate higher than the optimal temperate without blowing the safety fuse. A suitable thermometer with a range of over 250 deg C can be used, optimal temperature of the closed plates should be around 180 deg C. Professional servicing is recommended to resolve these issues, contact us for details.

The Straighteners do not heat up enough

One plate failed:

    •  Check to see if one of the plates is not heating, often one plate can fail leading to an overall temperature decrease. Generally, the design of ghds mean that if htey operate with one plate only, it will be the switch side plate that fails. The heater plate will require replacing.

Both plates warm:

    This could indicate a faulty thermostat if the temperature is below optimum temperature. This will need checking and or replacing.

Unusual noise or smell

 

  • Electrical Issues: Any buzzing sounds or burning smells are indicative of serious electrical problems. Unplug the straighteners immediately and consult a professional. 
  • Remember, attempting to repair electrical appliances on your own can be dangerous and might void any warranty on your device. It’s always safer to consult with a certified technician or the manufacturer for repairs

Essential Care Tips for Your ghd Hair Straighteners

0

Essential Care Tips for Your ghd Hair Straighteners

Introduction

ghd hair straighteners have become a staple in many beauty routines across the globe. Known for their quality and performance, these straighteners can last for years with proper care. Below are essential tips to ensure your ghd hair straighteners stay in top condition, providing you with sleek, smooth hairstyles every time.

Cleaning

Regular cleaning is crucial. Ensure the straightener is unplugged and completely cool. Use a slightly damp cloth to gently wipe down the plates. Avoid using harsh chemicals or abrasive materials which could damage the plates. A soft cloth can remove product residue and buildup.

Storage

After use, allow your ghd straighteners to cool down completely before storing them. It’s advisable to store them in a heat-resistant pouch or mat. Avoid wrapping the cord around the straightener as this can cause damage to the wires. Instead, loosely coil the cord next to the straightener.

Avoid Moisture

Always ensure your hair is completely dry before using the straighteners. Using them on damp hair can cause both damage to your hair and the straightener. Also, avoid using straighteners in a humid environment to protect the electronic components.

Handling and usage

Be gentle when using your ghd straighteners. Avoid dropping them as this can damage the ceramic plates or internal components. Also, ensure not to clamp down too hard on the hair, as excessive pressure is unnecessary and can damage both your hair and the straightener.

Professional Servicing

 If your straighteners start to malfunction, do not attempt to repair them yourself. ghd hair straighteners should be serviced by professionals like ourselves, who can properly diagnose and repair any issues without compromising the safety and functionality of the device. 

Conclusion

Maintaining your ghd hair straighteners is simple but essential. By following these care tips, you can prolong the life of your straighteners and continue to achieve beautiful, sleek hairstyles. Remember, a little care goes a long way in ensuring the longevity and performance of your ghd hair styling tools.

Back To Top
wefixghds long ogo 400x125 1
--- Terms & Conditions

Contact

Phone: 01695 550066
Email: help@wefixghds.com
We operate Monday – Friday 9am – 5pm
 
WeFixGHDs
56 New Court Way, Ormskirk, Lancashire, L39 2YT

WeFixGHDs are not associated to Jemella Limited or any of it’s trademarks.